Electric Power Tools
Description
?
HDMI USB KVM Extender HDMI Signal Extender?over Cat5e / Cat6 with HDBaseT
?
Introduction:
?
The HDMI USB KVM ( Keyboard , Video , Mouse ) Extender is a tool which can extend your HDMI signal over 328fts / 100meters to a compatible display . It is designed to convert HDMI signal to standard HDBaseT signal which can be transmitted by CAT5e / CAT6 / CAT7 cable . It also supports Transfer Bidirectional Infrared control signal and RS232 control signal . With LAN serving connection and external digital and analog audio capability that gives users the convenience of additional audio connection . It also supports the connection of USB host and 2 USB device ports . So you can control the Source in the Sink side which is 328fts outside , also you can control the Sink in the Source side which is 328fts outside using the HDMI Extender .
?
Specifications :
?
- - - -
# Video Bandwidth | # 340MHz / 10 . 2Gbps |
# Transmitter | # 1 x HDMI , 1 x LAN , 1 x USB - H , |
# Input Ports | # 1 x IR in , 1 x Audio in , 1 x RS232 , |
# 1 x Optical ( Spdif in ) , |
# Output Ports | # 1 x IR out , 1 x Optical ( Spdif out ) , |
# 1 x HDBaseT OUT, 2 x USB - D |
# Input Ports | # 1 x IR in , 1 x Optical ( Spdif in ) |
# 1 x HDBaseT IN , 1 x USB - H |
# Output Ports | # 1 x HDMI , 1 x LAN , 2 x USB , |
# 1 x IR out , 1 x ?Audio out , 1 x RS232 ,1 x Optical ( Spdif out ) |
# Power Supply | # DC 24V 1A |
# ESD Protection | # ± 8kV ( air - gap discharge ) |
# Human Body Model | # ± 4kV ( contact discharge ) |
# Dimensions ( mm ) | # 160 ( W ) X 97 ( D ) X 28 ( H ) |
# Weight | # 450g / TX, 450g / RX |
# Operating Temperature | # 0°C ~ 40°C / 32°F ~ 104°F |
# Storage Temperature | # - 20°C ~ 60°C / - 4°F ~ 140°F |
# Relative Humidity | # 20 ~ 90 % RH ( Non - condensing ) |
# Power Consumption ?( Max ) | # 12W |
- - - -
?
Package
?
- - - -
# HDMI USB KVM Extender Transmitter | # 1PCS |
# HDMI USB KVM Extender Receiver | # 1PCS |
# Wideband IR Tx | # 2PCS |
# Wideband IR Rx | # 2PCS |
# 24V/1A DC power adaptor | # 1PCS |
# Operation Manual | # 1PCS |
# Phoenix male jack | # 2PCS |
# Mounting ears | # 4PCS |
- - - -
?
Features:
1 . Fully compliant with HDMI 1 . 4 , and compatible with HDMI 2 . 0 ( 4K2K @ 60Hz with YCbCr 4 : 2 : 0 ) .
2 . HDCP2.2 and DVI compatible .
3 . Supports HDBaseT 2 . 0 specification over a single CAT5e / 6 / 7 cable up to 100m / 328ft .
4 . Supports pass - through of HD audio formats : LPCM2/5 .1 / 7 . 1 CH , Dolby Digital , DTS , Dolby TrueHD , DTS-HD Master Audio and more .
5 . POE ( Power Over Ethernet ) function support , either TX or RX powered 24V @ 1A,another don’t need power form the DC jack .
6 . Full HD support : 1080p @ 60Hz @ 24 / 36 / 48bit / pixels .
7 . Supports USB 2.0 control .
8 . Supports external Bi-Directional SPDIF IN / OUT and available for multichannel audio .
9 . Supports stereo audio with PCM 2CH .
10 . Transfer Bidirectional Infrared control signal together with the HDMI signal .
11 . Transfer Bidirectional RS232 control signal together with the HDMI signal .
12 . Transfer Bidirectional Ethernet signal together with the HDMI signal .
?
Operation controls and Functions :
?
1 . Transmitter Front Panel
?
?1 . Indicator LED :
# Power LED : illuminates when power has been supplied to the unit .
# Link LED : The connection status indicating lamp .
? Illuminate : The Transmitter and Receiver is good connections .
? Flashing : The Transmitter and Receiver is poor connections .
? Dark : The Transmitter and Receiver is no connections .
# HDCP LED : The HDCP status indicating lamp .
? Illuminate : The HDMI signal with HDCP .
? Flashing : The HDMI signal without HDCP .
? Dark : No HDMI signal .
# FW LED : Light is flashing on behalf of the unit work normally .
2 . IR IN : Chanel 1 IR Receiver. Connect with Wideband IR Rx .
3 . IR OUT : Chanel 2 IR Transmitter . Connect with Wideband IR Tx .
4 . RS232 TX/RX : Connect to a PC or Laptop with 3 - pin Relay cable for the transmission of RS - 232 commands .
5 . AUDIO IN: ?Connect to a PC or Laptop stereo output port via 3 . 5mm audio cable .
6 . USB-D : Connect to USB peripheral devices such as printer , keyboard, mouse, flash driver or … etc .
7 . USB-H : Connect from PC or Laptop for data transmit to or control from the Receiver’s USB - D slots .
8 . USB - H / USB - D SELECT : Select USB host or USB device .
Note : If the unit work to change the state , required again to power supply .
?
Transmitter Rear Panel
?
?
9 . UPDATE : Reserved for manufacturer use only .
10 . HDBaseT OUT : Standard HDBaseT signal output port . Connect HDBaseT receiver with a Cat5e / 6 / 7 cable .
11 . HDMI IN : This slot is where you connect the HDMI source .
12 . SPDIF IN ( Optical in ) : Connect to audio source equipment such as DVD or Blu - ray player for audio signal sending to Receiver’s SPDIF OUT ( Optical out ) .
13 . SPDIF OUT ( Optical out ) : Connect to speaker with coaxial input for audio signal output from Receiver’s SPDIF IN ( Optical in ) .
14. LAN : This slot provide Internet signal from receiver or to receiver .
15 . DC IN : Plug the 24V DC power supply into the unit .
?
Receiver Front Panel :
?
1 .?Indicator LED :
# Power LED : illuminates when power has been supplied to the unit .
# Link LED : The connection status indicating lamp .
? Illuminate : The Transmitter and Receiver is good connections .
? Flashing : The Transmitter and Receiver is poor connections .
? Dark : The Transmitter and Receiver is no connections .
# HDCP LED : The HDCP status indicating lamp .
? Illuminate: The HDMI signal with HDCP.
? Flashing: The HDMI signal without HDCP.
? ? ? ? ? ? ? ? Dark : No HDMI signal .
# FW LED : Light is flashing on behalf of the unit work normally .
2 . IR IN : Chanel 1 IR Receiver . Connect with Wideband IR Rx .
3 . IR OUT : Chanel 2 IR Transmitter. Connect with Wideband IR Tx .
4 . RS232 TX / RX : Connect to the devices ( project … etc ) that is to be controlled via 3 - pin Relay cable by RS - 232 commands .
5 . AUDIO OUT : Connect to speaker via 3 . 5mm audio cable .
6 . USB - D : Connect to USB peripheral devices such as printer , keyboard , mouse , flash driver or … etc .
7 . USB - H : Connect from PC or Laptop for data transmit to or control from the Receiver’s USB - D slots .
8 . USB - H / USB - D SELECT : Select USB host or USB device .
?
Note : If the unit work to change the state, required again to power supply .
?
Receiver Rear Panel
?
?
9 . UPDATE : Reserved for manufacturer use only .
10 . HDBaseT IN : Standard HDBaseT signal output port . Connect HDBaseT Transmitter with a Cat5e / 6/7 cable .
11 . HDMI OUT : This slot is where you connect the a HDMI equipped TV / monitor .
12 . SPDIF IN ( Optical in ) : Connect to audio source equipment such as DVD or Blu - ray player for audio signal sending to Transmitter’s SPDIF OUT( Optical out ) .
13 . SPDIF OUT ( Optical out ) : Connect to speaker with coaxial input for audio signal output from Transmitter’s SPDIF IN ( Optical in ) .
14 . LAN : This slot provide Internet signal from receiver or to receiver .
15 . DC IN : Plug the 24V DC power supply into the unit .
?
IR Cable Pin Assignments
?
?
Connection Diagram
POE ( Power Over Ethernet ) Application Example
?
Bidirectional Infrared control Application Example
?
Bidirectional RS232 control Application Example
?
Bidirectional Ethernet signal Application Example
?
USB control Application Example
?
Digital Audio bidirectional transmission Application Example
?
Application Example
?
?
Read More
SZ DODONET TECHNOLOGY CO.,LTD
VGA Video Converter,HDMI Switch Box,HDMI Signal Splitter
Address: 3rd floor ,Xinbaoyi electronic park ,Houting the third tech park ,Shajing town,Bao'an district ,Shenzhen ,China,
Shenzhen, Guangdong
China, 518000
Tel: 86-137-14429421
Fax: 86-137-14429421
