Used Machinery
Description
PA nylon Plastic Blow Molding Machine with 30L accumulator air tank?
?
?
Brief introduction
?
?
Features:
?
? 1. Structure design front and back is a complete set, no welding, heavy structure design make sure machine no any viberation when in production
? 2. Linear guide support the Carriage up down and clamping,reduce the friction between tie-bar and bushes,extend the life of machine.
? 3. Self-lubricated Copper bush used in all the moving point,make machine working more faster
and stable
? 4. Carriage up and down speed control valve installed,make sure machine working in high speed but no any noise and shake.
? 5. Linear transducer and stroke switch installed for better control and safety control
? 6. A return oil cycle design in the nose part of oil cylinder rod to avoid any leakage possibility
? 7. Automatic center lubrication system ,controller can set the lubrication time and frequency
? 8. Platform manually adjusted up and down,die head have twin-cylinder design
? 9. Fast response PLC control system, easy operating, endurable
? 10. Each hydraulic circuit can be controlled separately
? 11. 30L accumulator air tank installed for stable the blow air pressure and flow
? 12. Micro parison thickness adjustment along with micro blow pin center adjustment are controlled by 3-4bolt,easy for operator
? 13. Whole cooling system water pipe are using Oil pipe, longer life and remain low temperature? 14. Material loading gate and material level sensor is installed,can connect with auto-loader
? 15.Mould lifting crane is optional for easier mould installation
?
?
Machine specification:
?
MP80D-1T-5LAYER (70/70/35/35/25)
5Layer single head with View strip optional
?
(1). Extrusion unit
1. ?Main screw:70mm? with L/D:24/1 ?Screw RPM:15-60R.P.M
1) Heating zone:3zones?? Heating power:10.8KW
2) 2 Fan zones,Temperature can be individually controlled by PLC interface
3) extrusion motor size:18.5KW
4) Adopt Rexroth-Germany inverter ,size 18.5KW
5) Gearbox adopt top 3 China brand Yuyuan,model:ZLYJ-200
6) Main screw is using for the outer layer, thickness accounting 42.5%
?
2.? First layer screw:70mm with L/D:24/1 ?Screw RPM:15-60R.P.M
1) Heating zone:3zones?? Heating power:10.8KW
2) 2 Fan zones,Temperature can be individually controlled by PLC interface
3) Adopt Rexroth-Germany inverter ,size 18.5KW
4) Gearbox adopt top 3 China brand Yuyuan,model:ZLYJ-200
5) first layer after the outer layer,thickness accounting 42.5%
?
3. ?Adhensive screw:35mm with L/D:24/1 ?Screw RPM:15-60R.P.M
1) Heating zone:3zones?? Heating power::2.2KW
2) 1 Fan zones,Temperature can be individually controlled by PLC interface
3) Adopt Rexroth-Germany inverter ,size 2.2KW
4) Gear box using direct connection design more accurate and powerful
5) ?Adhensive located in Second and fourth layer,each layer thickness accounting:5%
?
4.? EVOH layer Screw diameter:35mm? L/D ratio:24/1 Screw RPM:15-60R.P.M
1) heating zone:3zones Heating power:2.2KW
2) 1 Fan zones,Temperature can be individually controlled by PLC interface
3) Adopt Rexroth-Germany inverter ,size 2.2KW
4) Gear box using direct connection design more accurate and powerful
5) EVOH between 2 layer adhensive ,accounting 5%
?
5．View strip screw size:25mm? L/D:24/1 Screw RPM:15-60R.P.M
1) heating zone:3zones Heating power:1.6KW
2) 1 Fan zones,Temperature can be individually controlled by PLC interface
# # Using Servo motor :size:1.5KW?
(2) Die head
? 1. Number of Head:Single
? 2. Type:FIFO
? 3. Heating zone:3,heating power:10KW
? 4. Die (Thickness)adjustment:4 Bolt adjustment
? 5 ?Material:38CrMoAlA,Cr12MoV
? 6. Hydraulic cylinder diameter for MOOG:120mm,stroke:20mm
?
(3) Clamping unit
? 1 Mould height:465mm,Mould width:520mm
? 2. Platen stroke:220-620mm.
? 3. clamping foce:150KN(15Ton,140kgf/cm2)
? 4. Locking cylinder diameter:120mm??? stroke:450mm
? 5. carriage cylinder diameter: 50mm stroke:540mm
? 6. Carriage moving type:Tie-bar and linear.
? 7. Locking Supporting arm,Hook,Copper platen balance ring using for strengthing?
? 8. Self-lubricated Copper bush using for all the moving part
? 9. Planten width:420mm
? 10. Platen height:465mm
?
(4) Blowing unit
? 1. Blow pin oil cylinder diameter:40mm ?stroke:150mm
? 2. pre-blow,multi-blow function can be optional
? 3. Blow pin tip cooling system
? 4. Blow pin center system is easiest micro control by 3 front bolt
? 5. Blow pin down
?
?(5)Cutter
? 1. Type:Hot cutter(straight cut)
? 2. Cutter cylinder dia:40mm,Stroke:200mm.
? 3. Dimmer model:2000VA
? 4. Supporting by 2 copper pole
? 5. Cutter wiring is using100m2anti-high temperature specialized type.
(protecting by plastic tube)
? 6. Cuting blade material:High grade stainless steel
?
(6) Hydraulic system
? 1. Pump motor:11KW
? 2. Hydraulic motor brand:Vickers-American
? 3. Hydaulic oil tank size:250L
? 4. Hydraulic valve and components: Vickers-American
? 5. MOOG hydraulic tank separate unit
?
?(7) Cooling System
?
? 1. Hydraulic cooling inlet size:1cinch
? 2. Mould cooling water main inlet size:1inch
? 3. Mould water pipe connect to mainifoild size: Φ12mm
? 4. Cooling water consumption:40L/min
? 5. Condernsor model:GLD-2.1
?
?
Read More
VAINO INTERNATIONAL LIMITED
HDPE Blow Molding Machine,Extrusion Blow Molding Machine,Automatic Blow Molding Machine
Address: Room1315,B# Ningbo Chamber Of Commerce Building,No.588 Tiantong South Road,Yinzhou District,Ningbo,China,
Ningbo, Zhejiang
China, 315000
Tel: 86-574-88054805
Fax: 86-574-88054565
