Used Machinery
Servo system plastic injection molding machine for making rubbish bin turn over box
M1800
Description
servo system plastic injection molding machine for making ?rubbish bin turn-over box
?
QUIET & LOW NOISE
The machine runs with low noise ,and will be much quieter in a low speed
?
RELIABLE HOLDING PRESSURE
? Comparing with all electric injection molding machine ,the time for pressure holding will be much longer and steady
?
OIL TEMPERATURE RISE SLOWLY
?Servo motor proportionally deliver hydraulic oil base on our needs,it’s can prevent unnecessary heat being generated even in some cases? does not require ,cooling .
?
?EXCELLENT CHARACTERISTICS INHERITANCE
? Outstanding machine stability ,being safety and dependability ,strong mechanical parts ,complete functional human-oriented operation system and long service life .
?
SPECIFICATION?
?
- - - -
?SPECIFICATION? | M-1800 |
ITEM | A | B | C | D |
??INJECTION??UNIT | ? |
?????????SCREW??DIAMETER | mm | 130 | 140 | 150 | 160 |
??????SCREW??L/D??RATIO | L/D | 24 | 22 | 20 | 19.2 |
???SHOT??VOLUME(THEORETICAL) | ? | 10619 | 12315 | 14137 | 16085 |
??????????INJECTION??WEIGHT(PS) | g | 9769 | 11330 | 13006 | 14798 |
??????????INJECTION??PRESSURE | Mpa | 183 | 158 | 137 | 121 |
??????????INJECTION??RATE | g/sec | 958 | 1111 | 1276 | 1452 |
?????????SCREW??SPEED | rpm | 95 |
CLAMPING?UNIT | ? |
?????????????CLAMP??TONNAGE | KN | 18000 |
??????????TOGGLE??STROKE | mm | 1600 |
??????????MIN.MOLD??HEIGHT | mm | 700 |
??????????MAX.MOLD??HEIGHT | mm | 1600 |
??????SPACE??BETWEEN??TIE??BARS | mm | 1570X1470 |
?????????????EJECTOR??TONNAGE | KN | 320 |
??????????EJECTOR??STROKE | mm | 420 |
?????EJECTOR??NUMBER | PC | 33 |
OTHERS | ? |
??MAX.PUMP??PRESSURE? | Mpa | 16 |
?????????HEATER??POWER | KW | 93 |
???PUMP?MOTOR??POWER | KW | 45+45+45 |
?????????OIL??TANK?CUBAGE | L | 2800 |
?????????MACHINE??DIMENSION(LxWxH) | M | 16.7X3.1X5.14 |
??????????MACHINE??WEIGHT | T | 110 |
- - - -
?
COMPONENT
?
- - - -
COMPONENT | BRAND&ORIGINAL | ? |
hydraulic?system | Servo |
hydraulic?motor | INTERMOT-ITALY-CHINA | ● |
servo?motor?control?system | HUICHUAN/PHASE-CHINA | ● |
hydraulic?pump | fixed?Pump | VICKERS?OR?YUKEN | / |
gear?pump | SUMITOMO-JAPAN | ● |
hydraulic?direction?valve | NORTHMAN-TAIWAN | ● |
propotional?flow?control?valve&propotiona l?pressure?control?valve | HNC-TAIWAN?FOR?BIG?MACHINE, SMALL?MACHINE?USE?DONGFENG-CHINA | / |
mould?adjust?hydraulic?motor | INTERMOT-CHINA? | ● |
hydraulic?safety?valve | NORTHMAN-TAIWAN | ?● |
electric?system | ? |
computer/controller | TECHMATION-TAIWAN | ● |
relay | SCHNEIDER-GERMANY | ● |
main?switch | LS-KOREA | ● |
linear?transducer | GEFRAN-ITALY | ● |
limited?switch | PANASONIC-JAPAN | ● |
breaker | CHENTAI-CHINA | ?● |
electric?motor | ZHONGDA-CHINA | / |
others | ? |
?High?pressure?hydraulic?pipe | GOODYEAR-USA | ● |
seals | VALQUA-JAPAN | ● |
pressure?meter | Tecsis-USA | ● |
automatic?lubrication? | SL-CHINA | ● |
screw? | JINGXING-CHINA?38CrMoAlA | ● |
- - - -
?
Selling?points
?
1.?More?fast?cycle:valve?panel?design?in?bigger?hole?with?bigger?oil?pipe.Oil?go?though?the?valve?more?fast?flow?and?the?Machine?action?more?goes?more?faster?in?mould?open?and?ejector?process.?
?
2.?Material?charging?more?faster:Adopt?proportional?control?for?backpressure,can?be?set?in?the?controller?,more?smart?and?easy?operation.when?material?charging,you?can?set?0?in?the?backpressure,so?the?charging?will?be?more?efficient?and?faster.make?sure?every?shot?to?be?more?accurate?than?manual?control?type.
?
3.?Adopt?Techmation?newest?verison?controller?which?is?more?fast?response?,more?output?and?input?can?be?use?for?connection?the?robot?in?future.
?
4.?Hydraulic?safty?protection?installed?in?both?front?and?rear?operation?door.when?any?door?is?open,the?hydraulic?system?will?be?shut?down?to?provide?more?safty?protect?for?the?operators.?
?
5.?Adopt?38CrmoAla?Material?for?key?in?toogle?part.more?endurable?in?using.other?supplier?may?use?40CR?or?45#?Steel
?
6.?Double?oil?tank?design:because?short?the?distance?for?the?oil?return?line?,the?hydraulic?system?response?is?getting?more?quicker.?In?the?meantime,this?design?will?reduce?the?oil?temperaure?,protect?the?oil?seal.
?
7.?Using?bridge?design?for?the?injection?unit,avoid?material?leakage?if?the?injection?unit?is?not?stay?in?the?same?level.
?
8.?Adopt?double?injection?cylinder?,more?faster?and?powerful.avoid?any?injection?less?or?injection?not?in?the?center?by?single?injection?cylinder
?
9. Screw?barrel?material?using?top?3?supplier?in?China
?
Platen size:
Read More
VAINO INTERNATIONAL LIMITED
HDPE Blow Molding Machine,Extrusion Blow Molding Machine,Automatic Blow Molding Machine
Address: Room1315,B# Ningbo Chamber Of Commerce Building,No.588 Tiantong South Road,Yinzhou District,Ningbo,China,
Ningbo, Zhejiang
China, 315000
Tel: 86-574-88054805
Fax: 86-574-88054565
