Electronic Signs

1. Home
2. Products
3. Electronic & Electrical
4. Electronic Signs

Share us

Reducing Dark Spots Cold Skin Care Machines 50 / 60 Hz with Switching Mode Power Adaptor

TP600

Send Inquiry

Description

Reducing Dark Spots Cold Skin Care Machines 50 / 60 Hz Switching Mode Power Adaptor

?

?

Specification:

?

- - - -
Product?Name | Cold?skin?therapy?equipment? | Character4 | Promotes?shinier?and?healthier?skin |
Character1 | Fast?cooling | Character5 | Improves?skin?tone?and?texture |
Character2 | Sooth?inflamed?wounds, headaches?and?sore?muscles | Color | white |
Character3 | Reduces?wrinkles | Size | 250*40*40mm |
- - - -

?

Introduction:

?

The TP600 is designed to make a small surface very cold without using traditional water wasting methods such as ice cubes, which can be damp and messy. It makes use of a Peltier thermal electric module, as well as a heat defuse plate and fan, to generate a local surface cooling effect. The solid aluminum head of the device can reach a temperature as low as -2℃ (but no lower than this to avoid making damage to the skin), depending on the room temperature and humidity.

Human body is capable of thermoregulation, allowing it to keep its temperature within certain boundaries. Thus when the low temperature aluminum head comes in contact with the skin’s surface, the local thermal shock stimulates the brain, instructing the heart to deliver more blood to the cold area in order to bring it back to normal body temperature. When used over time, new capillaries may be grown to accommodate the increased blood flow in the region. As a result, it will smooth away wrinkles and dullness of the skin and make the skin firmer. It is recommended not to use the TP600 for more than 15 minutes on each side of the face.

?

TP600?can?also?be?used?to?relieve?pain?and?skin?inflammations.?

? ? ? ? ? ? ? ? ? ? ? ??

?

Cold therapy:

?

The Cold Therapy is specially designed for claming down the skin after peeling.
The skin is sensitive after peeling treatment, so the cold treatment procures is necessary.

?

Ultrasonic therapy:

?

Ultrasonic utilizes sonic vibrations;The ultrasonic wave could
stimulate skin tissue and improve permeability of the membrane to promoted collagen tissue, reduced wrinkle
and invisible appeared fine line, also lift the skin result for younger and healthy look. Ultrasonic generate
frictional heat which accelerate blood circulation, muscle relaxation, and decompose the cellulite to break
down exceed fat. Bio-curve S Series& acute; ultrasound with 3 probes (Some model only comes with 2 probes)
provides non-surgical lifting. This machine utilizes sonic vibrations to reduce lines, leaving the skin firm and
smooth.

?

The?package:

?

There?are?five?items?in?the?gift-box；
# The?TP600?unit?
# Aluminum?head?tray
# The?switching?mode?power?adaptor?
# The?power?cable
# The?instruction?manual

Installation:
# Remove?all?items?from?the?package.?
# Insert?the?round?power?plug?of?the?switching?mode?power?adaptor?to?the?round?socket?at?the?end?of?the?unit,?and?the?other?end?to?the?power?cable.?
# Connect?the?plug?of?the?power?cable?to?a?suitable?a?wall?socket.?
# Place?the?aluminum?head?(with?the?head?facing?downward)?on?the?tray.

Operation:

?

Press the black power switch once gently to switch the device on. The yellow LED will be on, indicating that the temperature is cooling down. When the temperature goes below 12℃ the green LED will turn on, indicating that the device is ready for use. When the temperature reaches 0℃, the blue LED will turn on. When the temperatures reaches -2℃, the blue LED light will begin flashing, indicating that the temperature cannot go any lower. The time it takes for the device to cool down is dependent on environmental temperatures and humidity. When in use, the aluminum surface temperature will rise slightly due to absorption of body heat. To turn off the device, please hold the black power switch for 2-3 seconds until the light goes off.

?

Notes:


Clean the aluminum head using a damp cloth wet with water only. Do not use soaps or other chemicals.
Place the aluminum head in the tray when not in use, so as to collect condensation which may fall from the device.
Do not drop the unit. Doing so may damage the Peltier cooling module.

?

?

Read More